New 2025 CIE Chassis - Trailers
40' GN TANDEM
Stock # CIE40BLCLATL Web
2025 CIE, 40' GN TANDEM Semi-Trailers - Intermodal / Container (Chassis Only), 40' GN Tandem - GN402P5DF00 (Hutch) Specifications: 1.Function Carries one (1) 40' ISO container Meets all TOFC, AAR, DOT, FMVSS, ISO, ANSI, SAE and TTMA specifications 2.General Overall Length: 40'-8 1/2" (Excluded rear bumper) Overall Width: 96" Fifth Wheel Height: 48"±1" Rear Deck Height: 48"±1" Kingpin Location: 30 1/2" (From rear face of front bolster) Axle Spread: 49" Tandem Location: 54 1/2" (From rear face of rear bolster) Tare Weight: 6,600 Lbs. (±2%) Gross Vehicle Weight Rating: 73,800 Lbs. 3.Steel Structure & Components Material: High strength low alloy steel with yield strength not less than 50,000 psi used for the main rail hot rolled I-beams and other fabricated parts Painting: E-coat primer (min. 20 m) and Powder coating topcoat (approx. 60 m). 7 years warranty Topcoat color: BLUE Four (4) corner portions on front and rear bolster, touching corner casting of container, shall be painted Metal preparation: Commercial abrasive blast of all metal surfaces to achieve clean bare steel. Main Beam: 12 deep x 4 wide x 19 lbs./ft hot rolled I-section main beams, ASTM-A572 Grade 50 or equivalent Crossmember: 3/16\' thick x 3" wide x 9\' deep channel with integral gussets on top GN Beam: 5-1/4" deep x 4" wide I-beam, 1/2" thick flange and 1/4" thick web1/2 thick x 5 wide reinforcement strap is welded to the bottom flange of each gooseneck rail, starting at end of pickup plate and continuing behind the landing gear centerline Upper Coupler: 5/16" thick w/ 2" dia. drain holes, reinforced by 1/4" thick channel type kingpin supports SAF-Holland, Jost or Wallace Forge 2" AAR certificated kingpin Option: Use 1/4" thick pick-up plate if the kingpin suppliers cannot deliver the kingpins for 5/16" thick pick up plate in time. Front Bolster: 8" wide x 10" high, 1/4" thick open section with 3-1/2" chamfer in full length for gathering container in operation Front bolster provides full recessing of lights, and air and electrical connectors with 1 1/2 drain hole One piece corner casting welded on both ends Option: Use fabricated end cap if cast piece cannot be delivered on time. A flat triangular steel reinforcement plate welded on each side between the main rail and front bolster to reinforce the bolster. Reinforcement plate is 1/4 × 18.5 × 18.5 Gladhand and 7-way receptacle will be located in the center of front bolster Rear Bolster: 8" wide x 3/8" thick top plate with 6-7/8" wide x 8" deep x 1/4" thick "U" channel The triangular reinforcement plate is to be 1/4" x 18" x 18" with a 1-1/2 turned down lip with 1 1/2 drain hole Rear Bumper: Steel type rear bumper welded to the bottom of the rear bolster and rear of main rails, the vertical beam is H section type with 3/8 thick steel flange and 1/4 thick web The step guard is 3/16 x 4 x 4 square The bumper step is designed so that the legally mandated reflective tape is mounted in a recessed area, to prevent re